|
13) K24 Tilton 5.5" 2 Disc Carbon Clutch: $1750/each
k24 Tilton 5.5" 2 disc carbon clutch with lightweight k-series flywheel used half season. 2 complete clutches with flywheel. 2 avail.
|
|
12) B16 Block - Stock Call/Email for price
|
|
11) Head Studs
kb18c head studs $115
k20/24 head studs $115
b18a,b b20, b16 main studs $115
|
|
10) Weldon Fuel Pump: Call/Email for price
Used One Season. 2 avail.
|
|
9) K24 Golden Eagle Sleeved Block: $1200/each
k24 Golden Eagle sleeved block. Includes arp main studs and arp head studs. 90.5mm used 1 season. 2 avail.
|
|
8) Quartermaster Carbon Clutch: $2000/set
Quartermaster 5.5" 2 disc carbon clutch with lightweight k-series flywheeol used 4 passes 2 complete clutches no flywheel
|
|
7) TWM Throttle Bodies: $1350/set
52mm with horns cut and modified by Skunk2 for race application includes fuel rail and regulator. 1 set
|
|
6) Race Motors: $7500
Short block #0020 90.5mm bore RS sleeved short concrete fill. 96.5mm stroke crank done by Castillos with GSR journals. Wiseco pistons top gas ports deep pockets ring stack is 1.0 1.2 2.8. Cunningham ultralight rods 6.315 length 466grams weight. Stock oil pan and k20 oil pump.
|
|
5) Pistons:
CP 90mm bore deep pockets .880 c.h. .708 pin wire loc 320gram weight lateral gas ports small dome .300 tall 6cc ring stack is 1.0 1.2 2.8 $300/set
1 set CP 90.5mm bore deep pockets .880 c.h. .708 pin wire loc 265gram weight lateral gas ports small dome .300 tall 6cc internal milling ring stack is 1.0 1.2 2.8 $300/set
1 set Wiseco 90.5mm bore deep pockets .880 c.h. .708 pin wire loc 274gram weight top gas ports small dome 6cc ring stack is 1.0 1.2 2.8 1 set $300/set
Wiseco
CP
|
|
4) Rods
Cunningham 4340 steel ultralights 5/16 bolt 6.315 length 1.890 big end
diameter .858 big end width .708 pin diameter 466grams weight 4 sets.$500/set
BME Aluminum 3/8 bolt 6.285 length 1.771 big end diameter .757 big
end width .748 pin diameter 318grams weight 2 sets $300/set
Cunningham
BME
|
|
3) Custom Built Tri-Y Header: PRICE $700
These headers were custom built for the skunk2 race cars. They are made from
mild steel. Each header has been carefully spec'd out and uses merge
collectors for optimum performance. These headers will not fit street cars
and will probably need slight modification to fit your race car.
|
|
2) TWM K20A racing throttle bodies: PRICE $1500
The length of these throttle bodies have been modified to optimize
performance. these are the same throttle bodies used on the engine listed
above.
- Throttle bodies include:
- Fuel Rail
- Fuel Pressure Regulator
- Modified Throttle Linkage.
- Airhorns
|
|
1) USED 2450cc Skunk2 K24 Racing Engine: PRICE $8500
These engine were used by Skunk2 Racing used to run 9.80's at 140mph. With the right header and throttle body configurations, these engines make 320hp running on racing gasoline (tested on a Superflow chassis dyno, dynojet number should be about 10whp higher). These engines have been carefully inspected and serviced. long block only!!
Engine Specs:
- 13.5/13:8 : 1
- K24 Block (Sleeved by Golden Eagle)
- Ported K20A2 cylinder head
- Racing Valvesprings
- Forged Valves
- Titanium retainers
- prototype racing camshafts
- prototype racing camgears
- lightweight cunningham rods
- lightweight wiseco forged pistons
- castillos modified crankshaft
- head studs
- main studs
|
